Print

Calibration Kits, Enclosures, Software & Cables

Calibration Kits

We offer a number of accessories for the Telaire line, including calibration kits, enclosures, software and cables.

 

Calibration Kits

The Calibration Kit Model T2075NG includes the necessary components for calibrating the Telaire® 7001 and Ventotstat 8000 series models. The kit is housed in a carrying case (calibration not gas included). Calibration Kit Model T2076NG calibrates the Vaporstat T9002.

 

Accessory Enclosures

GE Sensing offers three enclosures to expand the Ventostat and Vaporstat installation options: Model T1508 Aspiration Box, Model T1505 Splash Resistant Enclosure, Model T1551/T1552 Outdoor Air Enclosure.

Software

Windows based VG Graphing Software allows you to easily download your IAQ measurements and customize graphs.

 


Check Stock at Authorized Distributors Contact GE’s Experienced Sales Team


Calibration Process

The calibration is simple and can be done in just a few minutes. Each CO2 model has a calibration process similar to the following:

• Connect the tubing assembly to the sensor and connect the regulator to the gas bottle.

• Initiate the calibration process by using the sensor buttons and display.

• The process is automatically run by the sensor and will signal upon completion.

• Last, disconnect the tubing and gas regulator.

main-accessoriesB-features
The illustration shows the complete set-up for calibrating a sensor with display.

 

T2075NG Components

The Calibration Kit Model T2075NG includes:

• Instruction sheet

• Tubing assembly

• Gas regulator with guage

• Carrying case

 

Calibrates the following models:

• Ventostat 8000

• Telaire 7000 Series

 

T2076NG Components

The Calibration Kit Model 2076 includes:

• Instruction sheet

• Tubing assembly

• Gas regulator with guage

• Carrying case.

• Flow Meter

 

Calibrates the following models:

• Vaporstat 9002

Enclosures Specifications

Enclosures are compatible with all Ventostat 8000 series and Vaporstat 9002 models.

T1508 Aspiration Box

The Model 1508 is designed for in-duct sampling of CO2 concentrations at flow rates greater than 400 fpm. Clear cover allows for observation of the sensor. Enclosure is screwed to the duct with probe inserted into airstream. Air sampling probe is 1 in (25.4 mm) diameter and 8 in (203.2 mm) long. Enclosure (ABS plastic) has knockouts for conduit connection. CO2 Sensor not included(T1551-T8001,T8002)(T1552-T8100,T8200).

T1505 Splash Resistant Enclosure

The Model 1505 is designed to protect the sensor in damp or wet environments which might occur in agricultural, industrial or food processing environments. This enclosure (ABS plastic) is designed to protect the sensor from dripping or sprayed water. The transparent cover allows for viewing of the sensor/display. Four diffusion ports allow for entry of CO2. Knockouts are provided for conduit connection. Response time of the sensor is slowed to approximately 30 minutes to measure a 90% step change in concentrations. Enclosure is designed to screw directly to a wall. CO2 sensor not included.

T1551 Outside Air Enclosure

The Model 1551 is a rugged weatherproof enclosure (ABS plastic), designed to allow the 8000 series sensor to operate in an outdoor environment and/or where ambient temperatures are below freezing. The 1551 is ideal for monitoring outside air or CO2 as a surrogate for combustion fumes in parking garages, tunnels and loading docks. This enclosure features a temperature control circuit and internal heaters to maintain the sensor within its normal operating temperature range, even if temperatures outside the enclosure are as low as –20°F (-29°C). Four diffusion ports allow for entry of CO2. Response time of the sensor is slowed approximately 30 minutes to measure a 90% step change in concentrations. Enclosure is designed to screw directly to a wall. CO2 sensor not included.
kits-dig-1

T1552 Outside Air Enclosure

As above but for the T8000 series (T8100, T8200, T8300).

Power consumption

24V, 1.5 Amp (maximum) – including sensor

2080 CO2 View Logging Software

CO2 View is a Windows based program that interfaces with the 8000 and 7000 series sensors. This easy to use program displays and graphs real-time CO2 levels at a user adjustable interval.

UIP 2072

Make adjustments and modify your 8000 series CO2 sensor parameters(T8002,T8001).

UIP T2090

Make adjustments to T8100,T8200 and T8300 series software and USB cable.

7001 Accessories

The Telaire 7001 hand held CO2 and temperature monitor is equipped with an output for recording data. The cable, Model 2070, can be used with devices that accept a 0 to 4V signal. A relative humidity and datalogging kit with graphing software, Model 2077, is available to long term monitoring.

 

Part 62933 is an adapter for international operation.


Descriptions English
Telaire Accessories Telaire Accessories


acrobat-reader